OILKLEEN NON-VARNISHING TURBINE FLUID PRODUCTS

PolyAlkylene Glycol (PAG) Synthetic Technology

FLUSH

Oil Flushing Services

FILTER

Electrostatic Oil Filtration

FILL

Non-Varnishing Fluids

Non-Varnishing PAG-based
Synthetic Turbine Fluid

OILKLEEN TURBINE FLUID-25 (TF-25)

Varnish build-up in Gas Turbine lube oil systems is the leading cause of unplanned shutdowns, system “trips”, and resulting in lost energy production. The root cause of these issues is the conventional petroleum-based turbine oil, which will oxidize through normal operation and form VARNISH and Sludge that cause servo valves to stick.

After 10+-years and over 100,000 hours of varnish-free performance, General Electric now includes PAG’s in their GEK 32568h specification for large frame gas turbines.

The OILKLEEN Non-Varnishing PAG-Based Synthetic turbine fluids are based off of many proven years of services with over 120+ Gas Turbines operating on PAG technology. It’s estimated by lab analysis and additive monitoring of many years in operation, that a Gas Turbine that converts to OILKLEEN Non-Varnishing PAG-based Synthetic turbine fluid can achieve 30+ years of service on a single charge of fluid. The OILKLEEN Non-Varnish PAG-base Synthetic turbine fluid is a combination of PolyAlkylene Glycol (PAG) base fluid and high-performance additive package which will not VARNISH.

When the OILKLEEN Non-Varnishing PAG-based Synthetic Turbine fluid is used, turbine bearings will typically operate at 5 degrees F to 10 degrees F lower temperature. This is due to the higher thermal conductivity of Group V PAG fluid versus Group I or Group II-IV oils.

Performance Advantages

OILKLEEN Non-Varnishing
PAG-based Synthetic Turbine Fluid

Non-Varnish and Sludge Forming

Polar fluid / Not a hydrocarbon base so it’s impossible to Varnish or form Sludge

Varnish removal

PAG fluids have natural detergency and solvency to dissolve and remove varnish from internal metal surfaces.

Reduced Friction

PAG Fluids have lower coefficient of friction and higher viscosity index so they use a lower viscosity grade, thus reducing friction and thermal demand on bearings. Typically, you will notice a 10 degrees F drop in bearing temperature.

Static Discharge on Filters

Reduced potential for static-discharge due to lower coefficient of friction and heat transfer than petroleum-based turbine oils.

High Temperature Stability

PAG molecules are very stable at high temperatures and resistant to thermal degradation at temperatures up to 120C (250F), resulting in longer life and increased reliability.

Gas Seal Compatibility

PAG-based Synthetic Turbine Fluid is compatible with commonly used seals, hoses, and metals.

Low Micro-dieseling potential

PAG -based Synthetic Turbine Fluid shows excellent air release times much lower than petroleum-based turbine oils.

Excellent Wear Protection

PAG-based Synthetic Turbine fluid; Four-Ball wear testing ASTM D4172 outperforms petroleum-based turbine oils even with up to 100,000 ppm of water.

NO VARNISH FORMATION

Why OILKLEEN PolyAlkylene Glycol (PAG) based Synthetic fluids don’t VARNISH?

Group V PolyAlkylene Glycol (PAG) base stocks are known to exhibit excellent thermal and oxidative stability as well as provide superior solubility characteristics as compared to Group I and Groups II-IV base oils. PAGs, by nature are relatively polar when compared with the relatively non- polar nature of Group I mineral oil, or with the increasingly non-polar Group II-IV base oils. Since PAG degradation compounds are polar, they will remain soluble and will not fall out of solution.

Low-Varnishing Turbine Fluid with enhanced PAG additive package (TF-32)

OILKLEEN Turbine Fluid 32 (TF-32)

The OILKLEEN Low-Varnishing Turbine Fluid 32 uses PAG-Based oil Modifier technology and combines with Group III Turbine Base oil and a high-performance additive package, to modify and change the polarity of the base oil and increase solvency of the petroleum-based oil to dissolve varnish build up and extend the life of the Turbine Fluid. The OILKLEEN Low-Varnishing Turbine Fluid with enhanced high-performance PAG additive package is a lower price point option with superior VARNISH removal and protection characterizes.

Base Oil Polarity Modifier for Petroleum-based oils

OILKLEEN RESTORE

OILKLEEN RESTORE is a high-performance base oil polarity modifier specifically designed for Petroleum-based oils that are experiencing VARNISH related issues or high MPC patch test results from lab analysis. OILKLEEN RESTORE will dramatically reduce varnish formation and RESTORE Severe levels of VARNISH shown on Varnish Potential ratings from the MPC patch test.

OILKLEEN RESTORE is not an antioxidant additive but instead modifies the polarity of the hydrocarbon BASE oil while dissolving VARNISH formation in the oil. OILKLEEN RESTORE is 100% soluble and compatible with all major commercial petroleum-based turbine oils and requires no FLUSHING or CONVERSION process to add. OILKLEEN RESTORE does increase the performance of the anti-oxidation additives in the oil and “Ruler” testing needs to be recalibrated to the new anti-oxidation levels. OILKLEEN RESTORE can increase the life of your Petroleum-based oil removing and preventing VARNISH related system failures or “TRIPS”.